![]() ![]() We regret that we are unable to answer questions regarding the update procedure using this system program.This will require servicing, so you will need to contact Roland service center near you if this occurs. If a power failure or similar accident occurs during the update process, the KATANA won't be able to start up in normal operating mode. Never power-off your KATANA while the update is in progress!.This update data may destroy the data or system program of other products. Never apply this update data to any product other than the KATANA.Computer (Windows or Mac) equipped with a USB port compliant with USB 2.0 or USB 3.0.Provide a cable suitable for connection to the computer you're using. * The update is carried out with the unit and the computer connected via USB. No sound produced immediately after making a USB connection.Noise when switching effects was reduced.Support for BOSS TONE STUDIO for KATANA was added.Setting the PC and CC numbers received by MIDI is now possible.SEND/RETURN is now settable for each individual TONE SETTING value.DELAY2, EQ (PATCH EQ), and GLOBAL EQ effect modules were added."PHASE 90E" and "FLANGER 117E" were added to TYPE for MOD/FX."LINE OUT AIR FEEL" and "CABINET RESONANCE" were added.A function to switch between BANK A/B has been added to TONE SETTING.To make settings for added functions, use BOSS TONE STUDIO for KATANA Version 2. Please refer to the "KATANA Owner's Manual" for detailed information in the. * Use BOSS TONE STUDIO for KATANA Version 2 to set SEND/RETURN to "ON." ![]() When the unit is updated to version 2.01, the SEND/RETURN values for BANK A and "PANEL" are set to "OFF." (This occurs when updating from version 1 to version 2.01.).* Use BOSS TONE STUDIO for KATANA Version 2 to set the Program Change number for each TONE SETTING. When the unit is updated to version 2.01, all TONE SETTING Program Change numbers are set to "1." (This occurs when updating from version 1 to version 2.01.).When a MIDI Program Change message and Control Change message are received simultaneously, the Control Change message is not applied.Selecting a TONE SETTING for which EQ is set to "OFF" yields sound for which EQ is set to "ON.".When TONE SETTING is set to "PANEL," after using the GA-FC (foot controller) to set respective effects to "OFF" and then again selecting "PANEL," the respective effects return to "ON.".When pressing and holding TAP on the GA-FC to switch between setting either the DELAY or DELAY2 delay time, the indicator on the GA-FC sometimes fails to flash.When switching between BANK A and B using a FS-5U unit connected to the EXP PEDAL jack on the GA-FC, in extremely rare cases, no sound is produced.When the POSITION value for GLOBAL EQ has been set using BOSS TONE STUDIO, the setting is sometimes not correctly applied to the audio.You can assign parameters to expression pedals with greater flexibility.It is now possible to assign the parameters you want to the effect knobs on KATANA's top panel."95E Pedal Wah" and "Roland DC-30 Analog Chorus-Echo" were added to TYPE for MOD/FX."GE-10" was added to TYPE for EQ (PATCH EQ) and GLOBAL EQ.When using reverb or other stereo effects, USB Audio OUT carries the stereo signal.The minimum value and maximum value settings of an expression pedal specified by "ASGN" return to their default values when the power is turned off.The SYSTEM parameter set in BOSS TONE STUDIO is initialized when KATANA version 2 is updated to version 3.Popping noise occurs when TONE SETTING is switched.Dedicated mode for using as a slave amp for the Katana Mk II's Stereo Expand feature (except KATANA-50).New Pedal FX section Wah and Pedal Bend effects can be set up in BOSS Tone Studio.Effects expanded to 65 total types Heavy Octave, Stereo Delay, and Pan Delay added. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |